这个HG261GS使用的是Broadcom菂芯片，型号是BCM68385_B0，RAM有128MB，NAND也是128MB，FS使用UBI。下面是分区信息：
0x0000002a0000-0x000002880000 : "rootfs"
0x000002880000-0x0000050e0000 : "rootfs_update"
0x000005100000-0x000005500000 : "data"
0x000000000000-0x000000020000 : "nvram"
0x000005500000-0x000005900000 : "ctmdw"
0x000005900000-0x000006100000 : "fhconf"
0x000006100000-0x000006500000 : "fhrootfs"
0x000006500000-0x000006f00000 : "fhlog"
0x000006f00000-0x000007f00000 : "fhbak"
0x000000020000-0x000002880000 : "image"
0x000002880000-0x0000050e0000 : "image_update"
0x000000020000-0x0000002a0000 : "bootfs"
跟HISI版的分区完全不一样了，应该是跟broadcom提供的SDK包有关。而且，这个版的kernel版本号3.4.11，HISI那个是用2.6的版本。
拆开机壳后，可以看到有UART的触点，这个是可以使用TTL来看打印信息，但不能输入，估计只作为log输出用了。下面是打印信息：
D%GHELO
CPUI
L1CI
PLLI
PMCB
HELO
CPUI
L1CI
4.1403_CT01-1.0.38-117.80
DRAM
----
PHYS
ZQDN
PHYE
DINT
TST1
TST2
PASS
----
ZBSS
MAIN
FPS0
BT00
0001
STOP
NAN9
NAN3
RFS1
NAN5
Base: 4.14_03_CT01
CFE version 1.0.38-117.80 for BCM96838 (32bit,SP,BE)
Build Date: Thu May 22 19:58:00 CST 2014 (sunjun@localhost)
Copyright (C) 2000-2013 Broadcom Corporation.
setAllLedsOn
Chip ID: BCM68385_B0, MIPS: 240MHz, DDR: 333MHz, Bus: 240MHz
RDP: 400MHz
Main Thread: TP0
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xbfc00000
NAND flash device: name , id 0xeff1 block 128KB size 131072KB
chipinfo 68385_B0
soc type 68385
wantype0=0x28, 40.gpio_value = 0
wantype1=0x27, 39.gpio_value = 0
lantype0=0x26, 38.gpio_value = 0
lantype1=0x25, 37.gpio_value = 32
lantype2=0x24, 36.gpio_value = 16
lantype3=0x23, 35.gpio_value = 0
boardType = 0x6,nvramData.szBoardId=968385SFU!
BOARD_ID_BY_GPIO=y
AFTER SYN nvramData.szBoardId = 968385SFU
AFTER SYN nvramData.ulVersion = 6
[WANGKAI] BpSetBoardId:968385SFU
[WANGKAI] wk_b:0
WK01
ddr_tm_base_address = 0xa0800000
WK01
WK01
WK01
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-45) : 968385SFU
Number of MAC Addresses (1-32) : 10
Base MAC Address : f8:c9:6c:d1:45:3e
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
GPON Serial Number : "FHTT6CD1453E"
GPON Password : " "
MC memory allocation (MB) : 0
TM memory allocation (MB) : 0
Voice Board Configuration (0-0) : LE9540
Creating CPU ring for queue number 0 with 32 packets descriptor=0x80669438
Done initializing Ring 0 Base=0xa220f7e0K End=0xa220f9e0K calculated entries= 32 RDD Base=0x0220f7e0K descriptor=0x80669438
Open PHY 1 on MAC 0 : link state = Down
Open PHY 2 on MAC 1 : link state = Down
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
WK01
Booting from only image (0xbfc20000) ...
Decompression OK!
Entry at 0x803ad0f0
Closing network.
rdd_ring_destroy
Starting program at 0x803ad0f0
Linux version 3.4.11-rt19 (yanliang@localhost) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Fri Sep 26 17:13:18 CST 2014
968385SFU prom init
CPU revision is: 0002a080 (Broadcom BMIPS4350)
Determined physical RAM map:
memory: 01400000 @ 06c00000 (reserved)
memory: 00400000 @ 06800000 (reserved)
memory: 06800000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00006800
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00006800
On node 0 totalpages: 26624
free_area_init_node: node 0, pgdat 804c2400, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 176 pages used for memmap
Normal zone: 22352 pages, LIFO batch:3
PERCPU: Embedded 7 pages/cpu @810d3000 s5088 r8192 d15392 u32768
pcpu-alloc: s5088 r8192 d15392 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 26416
Kernel command line: ro noinitrd irqaffinity=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 100184k/106496k available (3756k kernel code, 6312k reserved, 1055k data, 208k init, 0k highmem)
Preemptible hierarchical RCU implementation.
NR_IRQS:256
console [ttyS0] enabled
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Calibrating delay loop... 237.05 BogoMIPS (lpj=118528)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 Sep 26 2014 17:05:54
CPU revision is: 0002a080 (Broadcom BMIPS4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Brought up 2 CPUs
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xeff00000-0xefffffff]
pci_bus 0000:00: root bus resource [io 0xf1000000-0xf100ffff]
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skbFreeTask created successfully
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Sep 26 2014 17:13:06 initialized
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 16
init_bcm_tstamp: unhandled mips_hpt_freq=120000000, adjust constants in bcm_tstamp.c
bcm_tstamp initialized, (hpt_freq=120000000 2us_div=120 2ns_mult=0 2ns_shift=0)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
msgmni has been set to 195
io scheduler noop registered (default)
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=eff18095
After: NandSelect=40000001, nandConfig=15142200
DevId eff18095 may not be supported. Will use config info
Spare Area Size = 16B/512B
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 6574845b
timing2 not adjusted: 00001e96
ECC level changed to 4
OOB size changed to 16
BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0
Found NAND on CS0: ACC=f7441010, cfg=15142200, flashId=eff18095, tim1=6574845b, tim2=00001e96
BrcmNAND version = 0x80000500 128MB @00000000
brcmnand_scan: B4 nand_select = 40000001
brcmnand_scan: After nand_select = 40000001
handle_acc_control: default CORR ERR threshold 1 bits
ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 5.0 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_2k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0
brcmnand_reset_corr_threshold: default CORR ERR threshold 1 bits for CS0
brcmnand_reset_corr_threshold: CORR ERR threshold changed to 3 bits for CS0
brcmnandCET: Status -> Deferred
***** Found UBIFS Marker at 0x0029ff00
Creating 12 MTD partitions on "brcmnand.0":
0x0000002a0000-0x000002880000 : "rootfs"
0x000002880000-0x0000050e0000 : "rootfs_update"
0x000005100000-0x000005500000 : "data"
0x000000000000-0x000000020000 : "nvram"
0x000005500000-0x000005900000 : "ctmdw"
0x000005900000-0x000006100000 : "fhconf"
0x000006100000-0x000006500000 : "fhrootfs"
0x000006500000-0x000006f00000 : "fhlog"
0x000006f00000-0x000007f00000 : "fhbak"
0x000000020000-0x000002880000 : "image"
0x000002880000-0x0000050e0000 : "image_update"
0x000000020000-0x0000002a0000 : "bootfs"
UBI: attaching mtd0 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. sequence number: 2
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 37 MiB
UBI: number of good PEBs: 303
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 303
UBI: number of PEBs reserved for bad PEB handling: 3
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 235
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver usblp
i2c /dev entries driver
brcmboard: brcm_board_init entry
****************(BpGetResetToDefaultExtIntr),intr = 0
****************(BpGetLedIndicateExtIntr),intr = 1
LED: Button Interrupt 0x1 is enabled
led: onoff is (1)
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb4e00500 (irq = 9) is a BCM63XX
ttyS1 at MMIO 0xb4e00520 (irq = 10) is a BCM63XX
TCP: cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
*******initialize netlink succese!*******
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
8021q: 802.1Q VLAN Support v1.8
UBIFS: mounted UBI device 0, volume 0, name "rootfs_ubifs"
UBIFS: mounted read-only
UBIFS: file system size: 36188160 bytes (35340 KiB, 34 MiB, 285 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: zlib
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) readonly on device 0:10.
Freeing unused kernel memory: 208k freed
init started: BusyBox v1.17.2 (2014-09-26 17:20:28 CST)
starting pid 266, tty '': '/bin/sh -l -c "bcm_boot_launcher start"'
Mounting filesystems...
*****start VOIP CHECK!
thread id: 271
cp: can't stat '/fhbak/data_temp/*': No such file or directory
cp: can't stat '/fhbak/fhconf_temp/*': No such file or directory
Begin restore wlan calibration.....
Configuring system...
Loading drivers and kernel modules...
BOARDID=968385SFU DEVTYPE=simple UPLINK=gpon
bind error ,errno=Address already in use
*****start VOIP CHECK!
thread id: 316
gpon_stack: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
LOGGER driver Init Done : 0x86637480
MON: success
START GPON SerDes Init script
!!!! PLL locked !!!!!! !!!! RX CDR locked !!!!!! !!!! TX CDR locked !!!!!! GPON SerDes Initialization Sequence Done
# Created object
MON: success
MON: success
RDPA lan init
# Created object index=lan0>
MON: success
# Created object index=lan1>
MON: success
# Created object index=lan2>
MON: success
# Created object index=lan3>
MON: success
# Created object index=wlan0>
MON: success
# Created object dir=ds,index=0>
MON: success
# Created object
MON: success
# Created object
MON: success
# Created object
MON: success
MON: success
MON: success
MON: success
MON: success
RDPA lan init end
Creating CPU ring for queue number 0 with 128 packets descriptor=0xc047afa0
Done initializing Ring 0 Base=0xa5c85080 End=0xa5c85880 calculated entries= 128 RDD Base=0x05c85080 descriptor=0xc047afa0
MON: success
MON: success
rdpa filter init start!!
# Created object
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
MON: success
rdpa filter init end
lilac bridge fastpath. compiled Sep 26 2014 , 17:12:33
brcmchipinfo: brcm_chipinfo_init entry
NBUFF v1.0 Initialized
Initialized fcache state
Broadcom Packet Flow Cache Char Driver v2.2 Sep 26 2014 17:08:24 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
[FHW] pktDbgLvl[0xc05200e0]=0
[FHW] fhw_construct:
Initialized Fcache HW accelerator layer state
wl: Unsupported thread priority 0
flwStatsThread created
Constructed Broadcom Packet Flow Cache v2.2 Sep 26 2014 17:08:24
Broadcom Packet Flow Cache HW acceleration enabled.
i2c i2c-0: Failed to register i2c client gpon_i2c at 0x50 (-16)
i2c i2c-0: Failed to register i2c client gpon_i2c at 0x50 (-16)
i2c i2c-0: Failed to register i2c client gpon_i2c at 0x51 (-16)
i2c i2c-0: Failed to register i2c client gpon_i2c at 0x51 (-16)
Broadcom BCM68385_B0 Ethernet Network Device v0.1 Sep 26 2014 17:12:34
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: F8:C9:6C:D1:45:3E
eth1: MAC Address: F8:C9:6C:D1:45:3E
optical_wan_type = 1, WAN_GPON=1, WAN_EPON=2
Creating CPU ring for queue number 3 with 512 packets descriptor=0xc047b030
Done initializing Ring 3 Base=0xa4c84080 End=0xa4c86080 calculated entries= 512 RDD Base=0x04c84080 descriptor=0xc047b030
Loading PCM shim driver
eth0 Link UP 100 mbps half duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
Endpoint: endpoint_init entry
Endpoint: endpoint_init COMPLETED
Creating CPU ring for queue number 2 with 32 packets descriptor=0xc047b000
Done initializing Ring 2 Base=0xa3e14c80 End=0xa3e14e80 calculated entries= 32 RDD Base=0x03e14c80 descriptor=0xc047b000
[NTC ploamFsm] printSerialPasswd: SN=46:48:54:54:6c:d1:45:3e
[NTC ploamFsm] printSerialPasswd: PW=20:20:20:20:20:20:20:20:20:20
dgasp: kerSysRegisterDyingGaspHandler: gpon0 registered
[NTC ploamFsm] bcm_ploamCreate: ploam driver created.
Creating CPU ring for queue number 4 with 64 packets descriptor=0xc047b060
Done initializing Ring 4 Base=0xa537e080 End=0xa537e480 calculated entries= 64 RDD Base=0x0537e080 descriptor=0xc047b060
Broadcom 802.1Q VLAN Interface, v0.1
PCIe0: No device found - Powering down
PCIe1: No device found - Powering down
ERROR
loading sim card module
epon_chrdev_init()
Creating CPU ring for queue number 5 with 32 packets descriptor=0xc047b090
Done initializing Ring 5 Base=0xa3e65c80 End=0xa3e65e80 calculated entries= 32 RDD Base=0x03e65c80 descriptor=0xc047b090
EponOamQueueOpen
Creating CPU ring for queue number 6 with 64 packets descriptor=0xc047b0c0
Done initializing Ring 6 Base=0xa4ce3080 End=0xa4ce3480 calculated entries= 64 RDD Base=0x04ce3080 descriptor=0xc047b0c0
cpu Ring 6 has been flushed
oam: MAC Address: F8:C9:6C:D1:45:3E
[INF rdpadrv] rdpa_cmd_drv_init: Broadcom Runner Packet Processor Char Driver v0.2 Sep 26 2014 17:12:20 Registered. Device: bcmrdpa Ver:<251>
[INF rdpadrv] rdpa_cmd_drv_init: RDPA driver init: OK
rdpa cpu meter start!!
MON: success
MON: success
MON: success
MON: success
rdpa cpu meter end
Open TxPower...
Configuring factorymode...
Saving kernel bootup messages for dumpsysinfo...
Starting cardscan...
The simcard is first detect
the simdriver is remove
user: insert
Starting CMS smd...
===== Release Version 4.14L.03.2 (build timestamp 140926_1715) =====
IOCTL_FB_SW_SIMCARD_ACTIVE:OK
send apdu buf is:The transfer len is 7
0xa0,0xa4,0x0,0x0,0x2,0x7f,0x80,
send finished!
the buffer is exist
the rx_len is -2
IOC_WRITE: error happened
failed to write simcard
receive buf is:
0xa0,0xa4,0x7f,0x80,0x0,0x0,0x0The transfer len is 7
,0x0,0x0,
receive finished!
****the file index is 0. ****
send apdu buf is:
0xa0,0xa4,0x0,0x0,0x2,0x7f,0x80,
send finished!
the buffer is exist
the rx_len is -2
IOC_WRITE: error happened
failed to write simcard
The transfer len is 7
0xa0,0xa4,0x7f,0x80,0x0,0x0,0x0,0x0,0x0,
receive finished!
send apdu buf is:
0xa0,0xa4,0x0,0x0,0x2,0x6f,0x0,
send finished!
the buffer is exist
the rx_len is -2
IOC_WRITE: error happened
failed to write simcard
The transfer len is 5
0xa0,0xa4,0x6f,0x0,0x0,0x0,0x0,0x0,0x0,
receive finished!
get response is:
the buffer is exist
the rx_len is -2
IOC_READ: error happened
failed to read simcard
send apdu buf is:
0xa0,0xc0,0x0,0x0,0xf,
send finished!
the get response valuse is 0.
the file 0 is empty
the card is empty
the card_driver is inslot
>>loadConfig: getCardState got 0
>>loadConfig: processFlag got 0
ctrestore=0
Got primary config file from flash (len=26362), validating....
config file from flash (__primaryPsi) is valid, len=26362, loading into MDM....
set cardObj->cardStatus=0, fhCardStatus = 0, updateFlagP = 000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000, ret=0
get uploadpre from psp is FALSE
mdm_loadConfig end
Enter adjustForCard
set cardObj->cardStatus=FALSE
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
wlctl: wl driver adapter not found
Adjust WLAN Configuration, has configuration [0], num [0], defaultnum [2]
get boardid: 968385SFU
ip_tables: (C) 2000-2006 Netfilter Core Team
ip6_tables: (C) 2000-2006 Netfilter Core Team
-----------ENTER RCLIGD--------------
nf_conntrack version 0.5.0 (1568 buckets, 6272 max)
Host MIPS Clock divider pwrsaving is enabled
Energy Efficient Ethernet is disabled
ssk:error:28.993:rutSntp_restart:304:ruobing----getVoipDnsServerIP failed
sntp:error:29.045:main:385:No timezone specified.
Netfilter messages via NETLINK v0.30.
netdev path : eth0.0 -> eth0
BCMVLAN : eth0 mode was set to RG
Created new Tag Rule: dev=eth0, dir=1, tags=0, id=0
Created new Tag Rule: dev=dev_set_wanparam,if_name = eth0.0, wanid = 2, wantype = 0
eth0, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth0, dir=1, tags=2, id=0
Created new Tag Rule: dev=eth0, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth0, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth0, dir=0, tags=2, id=0
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(eth0.0) entered forwarding state
br_log_state call for send_to_user!
br0: port 1(eth0.0) entered disabled state
br_log_state call for send_to_user!
br0: port 1(eth0.0) entered forwarding state
br_log_state call for send_to_user!
eth0 Link DOWN.
message received before monitor task is initialized kerSysSendtoMonitorTask
ADDRCONF(NETDEV_UP): eth1: link is not ready
netdev path : eth1.0 -> eth1
BCMVLAN : eth1 mode was set to RG
Created new Tag Rule: dev=eth1, dir=1, tags=0, id=0
Created new Tag Rule: dev=dev_set_wanparam,if_name = eth1.0, wanid = 2, wantype = 0
eth1, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth1, dir=1, tags=2, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=0
device eth1.0 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1.0) entered forwarding state
br_log_state call for send_to_user!
br0: port 1(eth0.0) entered disabled state
br_log_state call for send_to_user!
br0: port 2(eth1.0) entered disabled state
br_log_state call for send_to_user!
br0: port 2(eth1.0) entered forwarding state
br_log_state call for send_to_user!
****** enable rstp *****
killall: rstp: no process killed
the rcl_loopback_read is 5, 300, untagged, 0xFFFA
.
device br1 already exists; can't create bridge with the same name
***vlanTag is untaged.***
vlan[0] is 0.
vlanTag is untagged, ethernetType is 0xFFFA
.
vlancount is 0.
ifr flag is 4099
eth0 is ok
MAC Address: (f8.c9.6c.d1.45.3e)
**************version 003**************.
ethernetType is 0xFFFA
.
********convert to int is :fffa**********
rstp uses obsolete (PF_INET,SOCK_PACKET)
rstp can not find vlan tag . use fffa mode.
write pid 919
begin create rstp thread!thread rstp
bridge_init: prority is 32768, hello is 2, delay is 15, max is 20
_check_stpm_config
stp_in_stpm_create
_stp_in_stpm_enable: Bf8c96cd1453e
STP_stpm_enable
STP_stpm_start
_stp_stpm_init_data
STP_port_init
STP_port_init
STP_port_init
STP_port_init
all, start stpm
changed port is 3.
looped flag is 0.
set port state:p04==>discarding
changed port is 2.
looped flag is 0.
set port state:p03==>discarding
changed port is 1.
looped flag is 0.
set port state:p02==>discarding
changed port is 0.
looped flag is 0.
set port state:p01==>discarding
changed port is 3.
looped flag is 0.
set port state:p04==>discarding
send pack is
ff,ff,ff,ff,ff,ff,f8,c9,6c,d1,45,3e,ff,fa,ff,ff,fa,00,00,02,02,4e,80,00,f8,c9,6c,d1,45,3e,00,00,00,00,80,00,f8,c9,6c,d1,45,3e,80,04,00,00,14,00,05,00,0f,00,00,00,00,00,00,00,00,00,00,00,0e,f9,00,00,00,00,
send vlan pack is
ff,ff,ff,ff,ff,ff,f8,c9,6c,d1,45,3e,ff,fa,ff,ff,fa,00,00,02,02,4e,80,00,f8,c9,6c,d1,45,3e,00,00,00,00,80,00,f8,c9,6c,d1,45,3e,80,04,00,00,14,00,05,00,0f,00,00,00,90,00,40,00,00,03,00,00,0e,f9,00,00,00,00,type is 9000, tag1 is 4000, tag2 is 3, tag3 is 0.
send vlan pack is
ff,ff,ff,ff,ff,ff,f8,c9,6c,d1,45,3e,ff,fa,ff,ff,fa,00,00,02,02,4e,80,00,f8,c9,6c,d1,45,3e,00,00,00,00,80,00,f8,c9,6c,d1,45,3e,80,04,00,00,14,00,05,00,0f,00,00,00,90,00,40,00,00,03,00,00,0e,f9,00,00,00,00,type is 9000, tag1 is 4000, tag2 is 3, tag3 is 0.
changed port is 2.
looped flag is 0.
set port state:p03==>discarding
send pack is
ff,ff,ff,ff,ff,ff,f8,c9,6c,d1,45,3e,ff,fa,ff,ff,fa,00,00,02,02,4e,80,00,f8,c9,6c,d1,45,3e,00,00,00,00,80,00,f8,c9,6c,d1,45,3e,80,03,00,00,14,00,05,00,0f,00,00,00,00,00,00,00,00,00,00,00,0e,f9,00,00,00,00,
changed port is 1.
looped flag is 0.
set port state:p02==>discarding
changed port is 0.
looped flag is 0.
set port state:p01==>discarding
lrwxrwxrwx 1 admin root 17 Jan 1 00:00 /fhrootfs/loopback.log -> /var/loopback.log
bridge_init OK ,begin recv_packet
pthread_join sucess!!!
eth0 Link UP 100 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
ADDRCONF(NETDEV_CHANGE): eth0.0: link becomes ready
br0: port 1(eth0.0) entered forwarding state
br_log_state call for send_to_user!
***** find poninterface is down ! ****
iptables: Bad rule (does a matching rule exist in that chain?).
ssk:error:35.007:rcl_cTPppoeEmulatorObject:1152:start up this node!
monitor task is initialized pid= 642
ssk:error:35.410:initFHVoiceBoundIpIfWanSideUpLocked:245:Failed to get WAN Connection object
create tid thread succes, main pid is 642
create tid2 thread succes, main pid is 642
call main_loop_back end
***** find poninterface is down ! ****
***** find poninterface is down ! ****
***** find poninterface is down ! ****
changed port is 3.
device_type is HG261G.
******* enter hg221_convert_port, and port is 3. *******
command is : bs /b/c port/index=lan3 emac_cfg={enable=yes} .
MON: success
Starting batchupgrade...
set port state:p04==>forwarding
changed port is 2.
device_type is HG261G.
******* enter hg221_convert_port, and port is 2. *******
command is : bs /b/c port/index=lan2 emac_cfg={enable=yes} .
MON: success
set port state:p03==>forwarding
changed port is 1.
device_type is HG261G.
******* enter hg221_convert_port, and port is 1. *******
command is : bs /b/c port/index=lan1 emac_cfg={enable=yes} .
MON: success
set port state:p02==>forwarding
changed port is 0.
device_type is HG261G.
******* enter hg221_convert_port, and port is 0. *******
command is : bs /b/c port/index=lan0 emac_cfg={enable=yes} .
MON: success
set port state:p01==>forwarding
httpget Daemon is running
--------shmID is 0-------
####entry recieve processLanHostInfoMsg
ssk:error:36.961:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName processLanHostInfoMsg
ssk:error:36.961:oal_lock:189:lock currently held by pid=1071 func=updateTr69cCfgInfo timeHold=29
ssk:error:36.962:oal_lock:194:timeoutMs=15000
facmode:debug:37.045:main:167:argv[1]=0, mode=0
facmode:debug:37.046:main:189:factory mode is disabled, exit!
####entrygetLayer2InterfaceForHost
optarg=0 shmId=0
tr69c:error:37.064:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName getFactoryStatus
tr69c:error:37.096:oal_lock:189:lock currently held by pid=642 func=processLanHostInfoMsg timeHold=85
tr69c:error:37.100:oal_lock:194:timeoutMs=6000
httpget:error:37.099:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName getInitMonitEnable
httpget:error:37.129:oal_lock:189:lock currently held by pid=1071 func=updateTr69cCfgInfo timeHold=25
httpget:error:37.130:oal_lock:194:timeoutMs=6000
ssk:error:37.139:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName processEthAssociateInfoMsg
ssk:error:37.139:oal_lock:189:lock currently held by pid=1071 func=updateTr69cCfgInfo timeHold=36
ssk:error:37.140:oal_lock:194:timeoutMs=15000
tr69c:error:37.153:updateTr69cCfgInfo:1163:could not build full path to 10.131.63.154
UPNPmngr Daemon is running
ENTER new thread
received msg: src=20 dst=65 type=0x10000250
receive unknown msg
WLmngr Daemon is running
optarg=0 shmId=0
optarg=0 shmId=0
useConfiguredLogLevel is 1
cmsObj_get MDMOID_UPNPMNGR_CFG is success
useConfiguredLogLevel is true
UpnpmngrCfg loggingLevel is Error
UpnpmngrCfg loggingDestination is Standard Error
baseEponMac is f8:c9:6c:d1:45:47
batchupgrade:debug:37.526:oalMsg_initWithFlags:122:commFd=3 connected to smd
batchupgrade:debug:37.526:oalMsg_initWithFlags:144:sent LAUNCHED message to smd
ITMS_REG_SUCCESS
ITMS_REG_SUCCESS
ITMS_REG_SUCCESS
start Quickinstallprocessmsgthread
!start Quickinstallprocessmsgthread
!Quickinstallprocessmsgthread end
!AppProcessMsg() start!
ITMS_REG_SUCCESS
WLMNGR-DAEMON:error:38.060:main:135:could not Fetch the Adapter and exit
device oam entered promiscuous mode
TkExtOamTaskInit success!
OMCI Configuration
===================================================
Debug-Flags = 0
Promisc-Mode = 0
Eth-Port-Type = ONT
Gpon LCDG or LOF state alarm
OMCI message capture enabled.
gpondef: MAC Address: F8:C9:6C:D1:45:40
netdev path : gpon0 -> gpondef
BCMVLAN : gpondef mode was set to ONT
netdev path : gpon0.0 -> gpon0 -> gpondef
BCMVLAN : gpon0 mode was set to ONT
gpon0.0 MAC address set to F8:C9:6C:D1:45:3E
device gpon0 entered promiscuous mode
device gpondef entered promiscuous mode
veip0 MAC address set to F8:C9:6C:D1:45:3F
netdev path : veip0 -> gpon0.0 -> gpon0 -> gpondef
BCMVLAN : gpon0.0 mode was set to ONT
veip0 MAC address set to F8:C9:6C:D1:45:3E
[MJ] OCS IPC SERVER Start.
***************************************************
* *
* GPON-ONT *
* *
* OMCI Stack Release: R2.9 V2.7 *
* ONU Release: G06D1.000000 *
* Build Date: Sep 26 2014 *
* Build Time: 17:18:59 *
* Operation Mode: LILAC_RDPA *
* *
***************************************************
starting pid 1252, tty '': '-/bin/sh -l -c consoled'
*****start VOIP CHECK!
thread id: 1261
bind error ,errno=Address already in use
BCM96838 Broadband Router
> device is register to itms
Created new Tag Rule: dev=gpon0.0, dir=1, tags=2, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=2, id=0
Created new Tag Rule: dev=gpon0.0, dir=1, tags=1, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=1, id=0
Created new Tag Rule: dev=gpon0.0, dir=1, tags=0, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=0, id=0
Created new Tag Rule: dev=gpon0.0, dir=1, tags=1, id=1
Created new Tag Rule: dev=gpon0.0, dir=0, tags=1, id=1
Created new Tag Rule: dev=gpon0.0, dir=1, tags=2, id=1
Created new Tag Rule: dev=gpon0.0, dir=0, tags=2, id=1
[ERROR ploamPort] get_gem_object_by_port_or_flow,1893: Failed to get GEM flow ID by GEM port: error -2
[ERROR ploamPort] ploamIOCgetGemPortCfg,871: ploamIOCgetGemPortCfg: error -2
[ERROR gponctl] gponCtl_getGemPort, 656: EINVAL_PLOAM_GEM_PORT (260)
[NTC ploam] bcm_cfgGemPort: gemPortID=0xfff usQ=0 dsmibidx 255 MaxGems 256
[NTC ploam] bcm_cfgGemPort: EncryptionInfo = 0
[NTC ploamPort] bcm_cfgGemPort: bcm_cfgGemPort: gemPortIndex = 1 gemPortID = 4095 error = 0
[NTC ploam] ploamIOCenableGemPort: gemPortIndex=0x1, gemPortId=0xfff, enable=1
mcast_gem <1> added to if
Created new Tag Rule: dev=gpondef, dir=0, tags=0, id=0
Created new Tag Rule: dev=gpondef, dir=0, tags=1, id=0
Created new Tag Rule: dev=gpondef, dir=0, tags=2, id=0
Created new Tag Rule: dev=gpondef, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=0, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
found ethName:eth0.0.config saved to flash***** fh_updatePonIntfStatus 001 ! ****
***** fh_updatePonIntfStatus 002 ! ****
***** begin fh_updatePonIntfStatus ! ****
***** fh_updatePonIntfStatus set to up ! ****
***** find poninterface is up ! ****
***** find poninterface is up ! ****
veip0.1 MAC address set to F8:C9:6C:D1:45:41
netdev path : veip0.1 -> veip0 -> gpon0.0 -> gpon0 -> gpondef
BCMVLAN : veip0 mode was set to RG
Created new Tag Rule: dev=veip0, dir=1, tags=0, id=0
Created new Tag Rule: dev=veip0, dir=0, tags=1, id=0
Created new Tag Rule: dev=veip0, dir=0, tags=2, id=0
[NTC ploam] ploamIOCcfgTcontAllocId: tcontIdx=0x0, allocID=0x101
device veip0 entered promiscuous mode
device gpon0.0 entered promiscuous mode
[ERROR ploamPort] get_gem_object_by_port_or_flow,1893: Failed to get GEM flow ID by GEM port: error -2
[ERROR ploamPort] ploamIOCgetGemPortCfg,871: ploamIOCgetGemPortCfg: error -2
[ERROR gponctl] gponCtl_getGemPort, 656: EINVAL_PLOAM_GEM_PORT (260)
[NTC ploam] bcm_cfgGemPort: gemPortID=0x81 usQ=0 dsmibidx 255 MaxGems 256
[NTC ploam] bcm_cfgGemPort: EncryptionInfo = 0
[NTC ploamPort] bcm_cfgGemPort: bcm_cfgGemPort: gemPortIndex = 2 gemPortID = 129 error = 0
[NTC ploam] ploamIOCenableGemPort: gemPortIndex=0x2, gemPortId=0x81, enable=1
Created new Tag Rule: dev=gpondef, dir=0, tags=0, id=1
Created new Tag Rule: dev=gpondef, dir=0, tags=1, id=1
Created new Tag Rule: dev=gpondef, dir=0, tags=2, id=1
Created new Tag Rule: dev=gpon0, dir=0, tags=0, id=1
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=1
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=1
Created new Tag Rule: dev=gpon0.0, dir=0, tags=0, id=1
Created new Tag Rule: dev=gpon0.0, dir=0, tags=1, id=2
Created new Tag Rule: dev=gpon0.0, dir=0, tags=2, id=2
Created new Tag Rule: dev=gpon0.0, dir=1, tags=0, id=1
Created new Tag Rule: dev=gpon0.0, dir=1, tags=1, id=2
Created new Tag Rule: dev=gpon0.0, dir=1, tags=2, id=2
Created new Tag Rule: dev=gpon0, dir=1, tags=0, id=0
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=0
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=0
Created new Tag Rule: dev=gpondef, dir=0, tags=0, id=2
Created new Tag Rule: dev=gpondef, dir=0, tags=1, id=2
Created new Tag Rule: dev=gpondef, dir=0, tags=2, id=2
Created new Tag Rule: dev=gpondef, dir=0, tags=3, id=1
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=2
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=2
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=0
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=0
Created new Tag Rule: dev=gpon0, dir=1, tags=0, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=0, id=2
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=3
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=3
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=1
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=1
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=4
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=4
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=2
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=2
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=5
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=5
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=3
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=3
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=6
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=6
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=4
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=4
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=7
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=7
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=5
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=5
Broadcom Packet Flow Cache flushing the flows
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=8
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=8
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=6
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=6
Broadcom Packet Flow Cache flushing the flows
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=9
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=9
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=7
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=7
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=10
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=10
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=8
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=8
Broadcom Packet Flow Cache flushing the flows
iptables: Bad rule (does a matching rule exist in that chain?).
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=11
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=11
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=9
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=9
iptables: Bad rule (does a matching rule exist in that chain?).
Broadcom Packet Flow Cache flushing the flows
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=12
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=12
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=10
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=10
iptables: Bad rule (does a matching rule exist in that chain?).
Broadcom Packet Flow Cache flushing the flows
********** pptp cmd enable. **********
iptables: Bad rule (does a matching rule exist in that chain?).
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=13
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=13
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=11
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=11Broadcom Packet Flow Cache flushing the flows
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=14
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=14
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=12
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=12
Broadcom Packet Flow Cache flushing the flows
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
***** find poninterface is up ! ****
***** find poninterface is up ! ****
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=15
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=15
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=13
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=13
netdev path : veip0.3 -> veip0 -> gpon0.0 -> gpon0 -> gpondef
BCMVLAN : veip0 mode was set to RG
Created new Tag Rule: dev=veip0, dir=1, tags=0, id=1
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=veip0, dir=1, tags=1, id=0
Created new Tag Rule: dev=veip0, dir=1, tags=2, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=veip0, dir=0, tags=1, id=1
Created new Tag Rule: dev=veip0, dir=0, tags=2, id=1
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=16
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=16
Created new Tag Rule: dev=veip0, dir=0, tags=1, id=2
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=14
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=17
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=14
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=18
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=17
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=15
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=15
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=19
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=18
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=16
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=16
device veip0.3 entered promiscuous mode
br1: port Created new Tag1(veip0.3) entered forwarding state
br_log_state call for send_to_user!
Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=20
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=19
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=17
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=17
recive kernel date from veip0.3, type=1, states = forwarding, recv len =60
eth num is : veip0.3, out of eth array!please check eth port setting!
portstate is 0, 0, 0, 0 ,0 ,0 !
pthread_join sucess!!!
br1: port 1(veip0.3) entered disabled state
br_log_state call for send_to_user!
recive kernel date from veip0.3, type=1, states = disabled, recv len =60
eth num is : veip0.3, out of eth array!please check eth port setting!
portstate is 0, 0, 0, 0 ,0 ,0 !
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=21
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=20
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=18
Created new Tag Rulbr1: port 1(veip0.3) entered forwarding state
e: dev=gpon0, dibr_log_state call for send_to_user!
r=1, tags=2, id=18
recive kernel date from veip0.3, type=1, states = forwarding, recv len =60
eth num is : veip0.3, out of eth array!please check eth port setting!
portstate is 0, 0, 0, 0 ,0 ,0 !
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=22
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=21
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=19
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=19
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=23
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=22
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=20
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=20
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=24
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=23
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=21
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=21
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=25
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=24
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=22
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=22
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
Created new Tag Rule: dev=gpon0, dir=0, tags=1, id=26
Created new Tag Rule: dev=gpon0, dir=0, tags=2, id=25
Created new Tag Rule: dev=gpon0, dir=1, tags=1, id=23
Created new Tag Rule: dev=gpon0, dir=1, tags=2, id=23
Created new Tag Rule: dev=gpon0.0, dir=1, tags=3, id=0
Created new Tag Rule: dev=gpon0.0, dir=0, tags=3, id=0
dev_set_wanparam,if_name = veip0.3, wanid = 3, wantype = 2
Bridge PPPoE Driver Module Build at Sep 26 2014 , 17:12:57
***** find poninterface is up ! ****
***** find poninterface is up ! ****
veip0.2 MAC address set to F8:C9:6C:D1:45:42
netdev path : veip0.2 -> veip0 -> gpon0.0 -> gpon0 -> gpondef
BCMVLAN : veip0 mode was set to RG
Created new Tag Rule: dev=veip0, dir=1, tags=0, id=2
Created new Tag Rule: dev=veip0, dir=0, tags=1, id=3
Created new Tag Rule: dev=veip0, dir=0, tags=2, id=2
***** find poninterface is up ! ****
***** find poninterface is up ! ****
pthreaADDRCONF(NETDEV_CHANGE): veip0.2: link becomes ready
d_join sucess!!!
Broadcom Packet Flow Cache flushing the flows
Broadcom Packet Flow Cache flushing the flows
Broadcom Packet Flow Cache flushing the flows
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
Broadcom Packet Flow Cache flushing the flows
iptables: Bad rule (does a matching rule exist in that chain?).
Broadcom Packet Flow Cache flushing the flows
********** pptp cmd enable. **********
recovered previous ppp session info ppp1.2(76912b8d0010/5fc4)
iptables: Bad rule (does a matching rule exist in that chain?).
Broadcom Packet Flow Cache flushing the flows
Broadcom Packet Flow Cache flushing the flows
ssk:error:49.250:ssk_main:1096:cannot handle msg type 0x10002252 from 95 (flags=0x20000000)
ssk:error:49.251:processItvDiagInfo:258:dhcpc_pid=1280, dhcpcInfo->addressAssigned=1, dhcpcInfo->ip=10.131.69.111, dhcpcInfo->mask=255.255.252.0.
pthread_join sucess!!!
gpon0.0: no IPv6 routers present
iptables: No chain/target/match by that name.
simpleARP start!!
simpleARP start!!
[RECV simpleARP REPLY] Reply receved from address 10.131.68.1
WARNING: The state match is obsolete. Use conntrack instead.
All services associated with veip0.1 is activated.
PPP: ppp1.2 Start to connect ...
--------shmID is 0-------
tr69c:error:53.237:cancelPeriodicInform:2351:request failed, ret=9003
tr69c:error:53.237:acsDisconnect:370:ACS Disconnect with error 1
ntpdatemain(496): tr069 wan ip is 10.131.69.111 !
ntpdatemain(500): tr069 wan dns1 is 192.168.200.1 !
ntpdatemain(504): tr069 wan dns2 is 0.0.0.0 !
ntpdatemain(531): get tr069 wan ip is 10.131.69.111 !
gethostbyname_tr069voip_ip
tr69c:error:53.270:retrySessionConnection:231:ACS connect failed, retryCount = 1, backOffTime = 8000ms
resolve flag = 1, ipaddr=10.131.69.111, dns1=192.168.200.1, dns2=0.0.0.0
gethostbyname_tr069voip_ip 10.131.69.111
pthread_join sucess!!!
saving ppp session info ppp1.2(76912b8d0010/0400)
netdev path : ppp1.2 -> veip0.2 -> veip0 -> gpon0.0 -> gpon0 -> gpondef
rm: can't remove '/data/imgFlag': No such file or directory
rm: can't remove '/data/cfgFlag': No such file or directory
tr69c:error:54.413:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName runRPC
tr69c:error:54.413:oal_lock:189:lock currently held by pid=1718 func=hgcGetConfigData timeHold=5
tr69c:error:54.414:oal_lock:194:timeoutMs=15000
=========================receive Configure-Request,it is LCP or IPCP?
===================================send pap Autherticate-Request
=========================receive Configure-Request,it is LCP or IPCP?
PPP: ppp1.2 IPv4 Connection Up.
***** find poninterface is up ! ****
***************************************
ipconnection status is Connected. !
ipconnection connectionType is IP_Routed. !
ipconnection X_CT_COM_ServiceList is TR069,VOIP. !
***************************************
***************************************
pppconnection status is Connected. !
pppconnection connectionType is PPPoE_Bridged. !
pppconnection X_CT_COM_ServiceList is OTHER. !
***************************************
***************************************
pppconnection status is Connected. !
pppconnection connectionType is IP_Routed. !
pppconnection X_CT_COM_ServiceList is INTERNET. !
***************************************
***** find poninterface is up ! ****
***************************************
ipconnection status is Connected. !
ipconnection connectionType is IP_Routed. !
ipconnection X_CT_COM_ServiceList is TR069,VOIP. !
***************************************
***************************************
pppconnection status is Connected. !
pppconnection connectionType is PPPoE_Bridged. !
pppconnection X_CT_COM_ServiceList is OTHER. !
***************************************
***************************************
pppconnection status is Connected. !
pppconnection connectionType is IP_Routed. !
pppconnection X_CT_COM_ServiceList is INTERNET. !
***************************************
dnsproxy:error:57.917:processCmsMsg:558:unrecognized msg 0x10002669
upnp:error:58.194:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName initLoggingFromConfig
upnp:error:58.195:oal_lock:189:lock currently held by pid=642 func=processPppStateChanged timeHold=1731
upnp:error:58.195:oal_lock:194:timeoutMs=60000
RTNETLINK answers: File exists
pthread_join sucess!!!
tr69c:error:58.584:cmsLck_acquireLockWithTimeoutTraced:101:mdmShmCtx->locked already have lock!callerFuncName setInformStatus
tr69c:error:58.584:oal_lock:189:lock currently held by pid=642 func=processPppStateChanged timeHold=2121
tr69c:error:58.585:oal_lock:194:timeoutMs=6000
init user limit module
user_proc_init
user_num_max=10
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.16.3: Couldn't find target `INPUT_OTHERSWAN'
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.16.3: Couldn't find target `bad_packets'
Try `iptables -h' or 'iptables --help' for more information.
WARNING: The state match is obsolete. Use conntrack instead.
iptables: No chain/target/match by that name.
WARNING: The state match is obsolete. Use conntrack instead.
iptables: No chain/target/match by that name.
WARNING: The state match is obsolete. Use conntrack instead.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
WARNING: The state match is obsolete. Use conntrack instead.
All services associated with ppp1.2 is activated.
receive msg 0x1000314, can not handle!
ntpdatemain(496): tr069 wan ip is 10.131.69.111 !
ntpdatemain(500): tr069 wan dns1 is 192.168.200.1 !
ntpdatemain(504): tr069 wan dns2 is 0.0.0.0 !
ntpdatemain(531): get tr069 wan ip is 10.131.69.111 !
gethostbyname_tr069voip_ip
pthread_join sucess!!!
gethostbyname_tr069voip_ip 10.131.69.111